UNLOCKING THE POTENTIAL OF MAN-MADE FIBRES WITH RING SPINNING
Fibre consumption is on the rise, and man-made fibres (MMF) play an important role in this. Blends containing various fibre materials are particularly popular and are found in an increasing number of applications. Rieter ring spinning machine G 38 offers unique solutions for processing MMF and blends.
As population growth and prosperity increase, so does the consumption of fibres across the globe. While this holds true for all staple fibres, the use of man-made fibres such as cellulosic staple fibres and synthetic staple fibres is growing particularly quickly. The consumption of cellulosic staple fibres is expected to double to 10 million tons by 2030 while the consumption of synthetic staple fibres is expected to grow by 48% to 28 million tons compared to 2015 (Figure 1). Rieter addresses these market needs and continuously develops innovative technology components
and solutions for MMF and blends for all end spinning processes.
MMF package for ring spinning
Synthetic fibres – usually polyester – and their blends with cotton are commonly processed on ring spinning machines. Different blends with cellulosic fibres are another popular application. In general, ring spinning is very flexible compared to other spinning processes and reacts less sensitively to fibre finish deposits which is a common challenge when processing MMF. Nevertheless, there are some technology elements on the ring spinning machine that have been specially developed for the characteristics of MMF and special settings that should be considered.
One of these technology elements is the bottom roller with a diameter of 30 mm. It helps to reduce the build-up of fibre lapping for fine fibres like MMF.
Thanks to an additional drive unit for the middle bottom roller, positioned in the middle of the machine, Rieter can offer long ring spinning machines also for MMF: The G 37 machine with semi-electronic drafting system drive can be equipped with up to 1 632 spindles and the G 38 machine with a fully electronic drafting system drive
with up to 1 824 spindles. High tenacity requires special solutions Due to their high tenacity, synthetic fibres cause high- er part wear during processing. This can be mitigated by installing separators with reinforced front edges.
These edges help to protect the separators from the fibre ends in the event of an ends down and increase the life cycle of the parts significantly. The high tenacity of synthetic fibres also poses challenges in terms of reliable detachment during the cop change procedure. If the detachment is unsuccessful, this can result in dragged yarn and a series of ends down, which affects yarn quality and efficiency. For this reason, a special SERVOgrip with a knife has been developed that reliably cuts off the yarn during the doffing process and prevents yarn breaks during start-up (Figure 2).
Correct settings improve yarn quality
Furthermore, the correct setting of the drafting system is important for yarn quality. The width of the drafting zone as well as the appropriate cradle nose bar and top apron should be defined according to the fibre length and the draft resistance of the raw material. For man-made fibres up to a cut length of 38 mm, the use of the stepped nose bar in combination with the specific active cradle without pin (Figure 3) improves yarn quality. With an active cradle, the top aprons are tensioned by a spring-loaded leading edge. Variations in apron tension are automatically compensated. It also permits lower cradle spacing for better guidance of the fibres, resulting in better yarn quality.
Tailor-made rings and travelers
Synthetic fibres do not self-lubricate the way cotton does and have a lower melting point. These properties are addressed by the oblique ORBIT ring and corresponding traveler in various surface finishes, which were specifically developed for spinning synthetic fibres. They guarantee smooth guiding properties and have a good heat diffusion to prevent melting spots. The ORBIT ring/traveler system handles the fibres very gently thanks to the large contact area between ring and traveler, as well as the reduced targeted surface pressure.
Compacting technology with wider application range
While it is less common, MMF can also be processed on compact-spinning machines. An important feature is the new sieve drum which is available as a standard on the compact-spinning machine K 48 and as an option on the K 47. A new coating has improved the durability of the sieve drum 20-fold compared to the previous series. The application range covers 100% cotton, viscose, polyester, and their blends.
MMF and sustainability
A lot of research and development is currently underway to make MMF more sustainable, with recycling offering the greatest opportunity. The key to this is polyester with its large market share. In 2019 the share of recycled polyester reached 14%, mostly using plastic bottles as feedstock. Numerous innovative initiatives have the potential to accelerate the transition to a circular economy.
An overview of all solutions for MMF in the Rieter system, from the blowroom to all four end spinning processes, can be found on www.rieter.com.
